Mould Temperature Controllers

Hengde Company is a well - established leader in the industrial temperature control industry. With years of experience and a focus on innovation, we offer top - notch mould temperature controllers that are trusted by industries worldwide. Our mould temperature controllers are designed to ensure efficient and reliable temperature control, backed by excellent customer service.   Preparation before starting the mould temperature controller: 1. Turn on the power after opening the valves of cooling water, circulating water, and hot water inlet and outlet.   2. Set the temperature control meter to 0℃ and press the start button.Press the start button, and the following situations may occur: 1) The pump reversal indicator light is on and the buzzer alarms; Processing: Turn off the power, swap any two phases of the external three-phase power line, and connect them back. 2) The pump overload indicator light is on and the buzzer alarms; Processing: Please press the reset button of the pump thermal relay and check whether the three-phase power is missing. 3) The lack of media indicator light is on and the buzzer alarms; Processing (water mould temperature machine): Check whether the water source switch is turned on, or the water supply pressure is insufficient. The water supply pressure of the water mould temperature machine is required to be 1.5KG. If the water pressure is not convenient to adjust, the low-pressure limit pressure of the low-pressure switch can be adjusted. Processing (oil mould temperature machine): Add thermal oil.   3. Set the thermostat to the required temperature.   Start-up process of mould temperature controller: * Water mould temperature controller: 1. Set the temperature to 0℃ first, circulate for 2 minutes, and then set it to the required temperature. 2. If it is not used for a long time, please turn off the main power, remove the connecting pipe, and drain the circulating water in this machine.   * Oil mould temperature controller: Warning: For the first installation or replacement of piping, after heating to the middle position of 1/3 of the liquid level tube, you need to wait for ten minutes before turning it on, otherwise the heating tube may be damaged. Please note! 1. Set the temperature to 0℃ first, circulate for 2 minutes, then set the temperature to 80℃, circulate for 5 minutes, and then set the temperature to 120℃ (if the pressure is unstable at 120℃, please reduce the temperature to 110℃, wait for the pressure to stabilize, and then increase it to 120℃), wait for the pressure gauge pressure to stabilize, and then set it to the required temperature. 2. If it is not used for a long time, please turn off the main switch, remove the connecting pipe and drain the circulating oil in this machine.   Mould temperature controller shutdown process: 1. When shutting down, it is best to lower the temperature of the water mould temperature controller to below 40℃ first, and the oil mould temperature controller is best to lower the temperature to below 80℃ before shutting down, which can extend the service life of the pump and heating tube. 2. If not used for a long time, please turn off the main switch, open all ball valves, and discharge the circulating oil/water in the system.   At Hengde Company, we are committed to providing not only high - quality products but also continuous support. Our technical team is always ready to assist you, ensuring your production processes run smoothly with our mould temperature controllers.   Choose Hengde，Choose Perfect Mould Temperature Controller！

As a pioneer in the field of industrial temperature control, Hengde has always been committed to developing and providing advanced temperature control solutions. In the field of composite mold die casting, which is full of challenges and opportunities, Hengde has provided key mold temperature controller products to many companies with its outstanding technical strength and rich industry experience, helping companies improve production efficiency and product quality.   The head of a well-known aerospace parts production company that has cooperated with us for many years gave feedback: "Before using Hengde composite material compression molding temperature controller, we often had quality problems such as bubbles and uneven strength in the products during filament winding and compression molding processes due to unstable temperature control, and the scrap rate remained high. Since the introduction of Hengde temperature controller, these problems have been solved. Its temperature control accuracy is extremely high, and it can be accurately regulated according to the temperature curve we set, which greatly improves the quality stability of the product. Moreover, its efficient heating and cooling system has shortened our production cycle by nearly 30% and significantly reduced production costs. Hengde temperature controller is really a powerful assistant for us to improve production efficiency!"   The following are common and key application scenarios of mold temperature controllers in composite material molding processes: 1. Filament winding: In the filament winding molding process, the fiber is first fully impregnated with resin through the resin glue tank, and then wound on the continuously rotating core mold according to a carefully designed rule. After winding, the glue needs to be heated to solidify and mold. In this process, Hengde mold temperature controller can accurately control the heating temperature to ensure that the glue is uniformly cured under suitable temperature conditions, thereby improving the strength and stability of the winding products and meeting the stringent requirements of high-end fields such as aerospace for material performance.   2. Pultrusion: For the pultrusion process, the carbon fiber roving or its fabric is pulled by external force and goes through the steps of dipping, extrusion molding, heating and curing, and fixed-length cutting in sequence. Hengde composite material mold temperature controller plays a key role in the heating mold link. Through precise temperature control, it can significantly speed up the curing time, greatly improve production efficiency while ensuring product quality, and meet the needs of large-scale production in industries such as automobile manufacturing.   3. Resin transfer molding (RTM): In the resin transfer molding process, the reinforcement material is first made into a preform and placed in a closed mold, and then the resin is injected into the mold under the dual action of vacuum and pressure to cure it. Hengde mold temperature controller effectively speeds up the curing speed by accurately heating the mold, greatly improving production efficiency, and has been widely used in fields such as electronic equipment component manufacturing.   4. Compression molding: Compression molding is a process in which the molding material is placed in a metal mold and solidified under specific pressure and temperature conditions. In many compression molding processes, such as short fiber compression molding, felt compression molding, rag compression molding, lamination compression molding, winding compression molding, fabric compression molding, directional laying compression molding, preformed embryo compression molding, sheet molding compound compression molding (SMC compression molding), etc., Hengde mold temperature controller plays an indispensable role. It can accurately adjust the mold temperature according to different process requirements to ensure that the quality of the molded products is stable and meets high standards.     Through its wide application in these key molding processes, Hengde composite compression mold temperature controller plays a vital role in aerospace, automobile, electronics and other fields with extremely high material performance requirements. It not only helps companies manufacture high-quality composite products, but also promotes the technological progress and development of the entire industry. Hengde will continue to uphold the spirit of innovation, continuously optimize product performance, provide better temperature control solutions for more industries, and work with customers to create a brilliant future.   Choose Hengde，Choose Perfect Mold Temperature Controller！